Free Republic
Browse · Search
News/Activism
Topics · Post Article

Skip to comments.

Heavy Weight Bullets In The .44 Magnum
Guns Magazine ^ | December 2001 | John Taffin

Posted on 02/22/2005 2:46:34 PM PST by 45Auto

Most shooters who have been around a fair amount of time know that Elmer Keith's writings about the .44 Special from the late 1920s into the mid-1950s were directly responsible for the advent of the .44 Magnum. He did not invent the cartridge, per se. However, without his articles about taking big-game with big-bore sixguns -- especially when chambered in the .44 Special and using what is now known as the "Keith Load" of a 250-grain, hard-cast bullet of his design at 1,200 fps from a 7 1/2-inch sixgun -- we would in all probability have never seen the .44 Magnum. He not only spent 30 years paving the way, he also negotiated directly with Remington and Smith & Wesson to bring about the ammunition and the sixgun to shoot it.

Keith was not an overnight sensation by any means. He started like most of us, from nowhere, knowing next to nothing. In fact, nearly 20 years after the .44 Special had been introduced by Smith & Wesson, he had yet to see one. Remember that in Keith's early years there were no gun magazines as such, and the closest thing to instant communication was a letter that took several weeks to travel across the country. He was simply a young, hard working cowboy in the 1920s who was enamored with sixguns, mostly the old Colt SAA .45, which in his time and economic condition were probably black powder specimens that had seen better days.

Genesis Of The .44 Magnum

In the early 1920s, Keith had an experience that changed his life forever. He decided to celebrate the Fourth of July by tiring his old black powder .45 Colt 5 1/2-inch SA. He went upstairs and onto the back porch of his little ranch house to make some noise.

"When the gun rose from the recoil of the first cartridge, I unconsciously hooked my thumb over the hammer spur and thus cocked the gun as it recovered from recoil. When I turned the next one loose, I was almost deafened by the report and saw a little flash of flame. My hand automatically cocked the gun and snapped again, but no report. I stopped then, knowing something was wrong. The upper half of three chambers was gone. Also one cartridge and half of another case. Also the top strap over the cylinder. My ears were ringing, otherwise I was all OK" (The American Rifleman, August 15, 1925).

This was described in a letter to the editor of The American Rifleman and would begin Elmer Keith's long, colorful and tremendously influential career as a gun writer. When the above "accident" was investigated, it was found that Keith had been using heavy .45 Colt loads in the SAA made up with 300-grain bullets with a diameter of .458 inch originally intended for use in the .45-90 lever-action Winchester. Not only that, it also appeared that he had aided the ignition process by crushing the black powder into a finer grain size.

His old Colt simply died that morning, and Elmer Keith switched to the .44 Special. By 1929 he had a full-blown article in The American Rifleman about his famous Number Five Single Action .44 Special that he built to be, as he called it, The Last Word.

When Keith got his .44 Magnum, he got even more than he had asked for. All he wanted was his .44 Special loading of a 250 grain, hard-cast bullet at 1,200 fps. He suggested new, longer brass so that this load would not chamber in older, weaker guns. Ammunition manufacturers were afraid that early .44 Special handguns could not handle the load. Instead of duplicating the Keith Load for the .44 Special, Remington came out with the .44 Remington Magnum with a 240-grain bullet at 1,400+ fps. Keith was ecstatic about the new load, and about the Smith & Wesson .44 Magnum sixgun.

It is interesting to read the early reports. Keith downplayed the recoil of the new cartridge. Major Hatcher of The American Rifleman staff likened it to being hit in the palm with a baseball bat. For most of us, reality was somewhere in-between Keith and Hatcher, probably leaning in Hatcher's direction. The .44 Magnum kicked! It kicked hard!! Especially in the 4-inch Smith & Wesson .44 Magnum with the plain clothes stocks that Elmer preferred, and definitely in the Ruger Blackhawk with a grip frame that was identical to that found on the Colt Single Action Army. Over the years, I have learned to handle the recoil of the .44 Magnum by practice, by using hand-filling, custom stocks and, most assuredly, by welcoming new sixguns that added extra weight over the 3pound heft of the original .44 Magnums.

I also learned something else. Going back to Keith's original blow-up story, I noticed that he was using heavyweight bullets, not the 255-grain bullet standard for use in the .45 Colt at that time. Why? I would guess he was looking for greater power and deeper penetration for use on big-game animals. When he switched to the .44 Special, he also designed a heavyweight .44 bullet, which was produced by the old firm of Belding & Mull. However, remember that in the early stages of his sixgunnin' life he was still learning. His 280-grain .44 Special bullet had a very blunt, rounded nose, and he soon found that it was lacking in long-range accuracy. He went back to the drawing board and came up with the classic #429421 250 grain, semi-wadcutter bullet, which everyone knows today as the Keith Bullet. When the .44 Magnum arrived, he used the same bullet and simply increased the muzzle velocity by 200 fps over his .44 Special loading. This was his standard load for every purpose until he suffered his terribly disabli ng stroke at the age of 81.

For at least 25 years the Keith Load was the standard load for the .44 Magnum, just as for 25 years earlier the .44 Special loading from Keith had been the standard. That is a half-century of tremendous influence on .44 shooters by one man! Once the .44 Magnum arrived, many sixgunners began to take a serious look at hunting with a handgun. They also found very quickly than if they did want to hunt, they would have to load their own ammunition because there was very little available on the shelves which was truly suitable. The Keith load has served us well.

Heavier Can Be Better

Then in the late 1970s, a new influence began to be felt. J.D. Jones founded SSK Industries, which was dedicated to providing the best possible products for handgun hunters. Much of his early work was with wildcat chamberings in the Thompson/Center Contender. One of those wildcats was the .430 JDJ, which was simply the .444 Marlin trimmed back. There were few bullets available, so Jones designed his own as well as supplying bullet molds. One of these bullets was a 320-grain, flat-nose that he would soon discover worked superbly in .44 Magnum sixguns.

I acquired one of Jones' early molds for this bullet and used it extensively in a custom 10-inch Ruger Super Blackhawk over 23.5 grains of WW680 for 1,400 fps. Now we had the same velocity as the original factory loaded .44 Magnum but with 80 grains more bullet! A new era had dawned for the .44 Magnum. Today we are fortunate to have heavyweight bullets, both hard cast and jacketed, available from a number of suppliers, as well as excellent bullet molds for casting our own.

1. Accuracy: The longer a bullet is in relation to its diameter, the more accurate it normally is. It is a rare .44 Magnum sixgun that does not shoot 300- to 320-grain bullets more accurately than it does 240- to 250 grain bullets.

Why use heavyweight bullets in the .44 Magnum? There are two reasons:

2. Big Game Hunting: To be successful as a handgun hunter, you must understand the four Ps: Placement, Power, Performance, and Penetration. Placement refers to where the bullet hits the target; Power, the muzzle energy; Performance, whether it expands or not; and Penetration, just how deeply into the animal we can expect the bullet to go. The latter is extremely important when hunting large or dangerous animals. And the simple fact is that heavy bullets penetrate more deeply.

Cast Heavyweights

Let us look at some of the heavyweight bullets used in the .44 Magnum, beginning with 10 cast-bullet loads. All were assembled using Starline's excellent and durable .44 Magnum brass, CCI #350 Magnum Large Pistol primers and Redding's equally excellent .44 Magnum carbide dies. Loads were chronographed over Oehler's Model 35P. Six powders normally used for heavy duty Magnum loads were pressed into service:Alliant's #2400, Accurate Arms' AA#9, Hodgdon's H110, the relatively new Lil' Gun, H4227 and Winchester's 296. There are also some loads included with Unique and BRP's 290-grain, Keith-style bullet simply because I shoot so many of these in older .44 Magnums. Other bullets are also shown with Unique loads for the simple reason that heavyweight bullet loads in the .44 Magnum need not always be shot at full power.


TOPICS: Miscellaneous
KEYWORDS: ammo; banglist; hunting; rkba; shooting
Navigation: use the links below to view more comments.
first 1-2021-4041-51 next last

1 posted on 02/22/2005 2:46:35 PM PST by 45Auto
[ Post Reply | Private Reply | View Replies]

To: 45Auto

The 290-grain, gas-checked, Keith-style bullet is my most used heavyweight .44 bullet. I have the NEI double-cavity mold for this bullet. BRP also supplies excellent ready-cast bullets of this design that actually weigh 290 grains. I have two favorite loads for this bullet: 21.5 gralns of H110 for 1,350 to 1,400 fps, and 10.0 grains of Unique for 1,100 tol, 150 fps. The former is used in currently manufactured heavy-duty .44 Magnums, while the latter mostly sees service in .44 Magnums built in the 1950s, namely the original Smith & Wesson M29 and Ruger .44 Blackhawk (flat-top).

Bull-X offers a Bill Wilson designed, 300-grain flat-point that weighs 305 grains in my alloy. This bullet has a long tapered nose with a full-caliber shoulder band and one wide grease groove. I order them unsized and unlubed so they may be tailored for each gun I intend to use them in.

Lyman offers bullet casters two heavyweight .44s, #429650GC, a Keith-style with one large grease groove and a gas-check with a hard-cast weight of 306 grains. Bullet #429649GC is heavier at 331 grains. It basi cally offers the same case capacity as the Keith-style bullet with a much heavier nose of the RNFP, or round-nosed, flat-point design. From RCBS comes another Keith-style heavyweight .44 bullet, #44-300SWC that weighs out at 298 grains with my hard alloy. It is very similar to the Lyman design with slightly more case capacity and a slightly longer nose.

From Oregon Trail Bullet Co. we have a 300-grain TC (Truncated Cone) that weighs out at 299 grains. This bullet puts most of the weight in the body with a very short nose. This maybe the choice if one has a lever-action that is reluctant to feed the longer bullets.

Finally we come to the heavyweight bullets designed by J.D. Jones of SSK Industries. Bullet #285.429 FP weighs in at 281 grains with one very large grease groove and two crimping grooves for use in short or long cylindered revolvers. All loads assembled herein used the top groove for use in any cylinder length or lever-action rifle. Last, but certainly not least, is the bullet that started it all, SSK's #310.429, another flat-point that with my hard alloy weighs 302 grains. This bullet has a full caliber shoulder in front of the crimping grooves, a plain base, and three grease grooves. It has a great reputation for taking big game with a .44 Magnum.

A Wealth Of Jacketed Bullets

At least five companies now offer excellent jacketed, heavyweight bullets for the .44 Magnum: Hornady's 300-grain XTP-JHP; Northern Precision's 280,310 and 325 grain; Nosler's 300-grain JHP; Sierra's 300-grain JHC; and Speer's 300 JFP. You will note that of the four major manufacturers, three provide hollow point versions of their 300-grain bullets, while Speer goes with a flat-point. Northern Precision custom tailors their bullets for individual needs, and they can be ordered with different jacket thicknesses for the game that is going to be hunted.

Two sixguns and one levergun were used for chronographing these loads, an 8-inch Dan Wesson .44 Magnum, a Freedom Arms 10-inch .44 Magnum, and a Winchester Model 94 Trapper .44 Magnum with a 16-inch barrel.


2 posted on 02/22/2005 2:47:47 PM PST by 45Auto (Big holes are (almost) always better.)
[ Post Reply | Private Reply | To 1 | View Replies]

To: 45Auto

Lots of reloading data at the end of this article.


3 posted on 02/22/2005 2:48:13 PM PST by 45Auto (Big holes are (almost) always better.)
[ Post Reply | Private Reply | To 2 | View Replies]

To: 45Auto

--not that I am about to damn any class of firearms or shooters, but I always have to smile at the disciples of Elmer, who were largely dismissive of the .30-30 category of cartridges for deer hunting when they were available only in rifles but think of them as great in handguns---


4 posted on 02/22/2005 2:54:38 PM PST by rellimpank (urban dwellers don' t understand the cultural deprivation of not being raised on a farm)
[ Post Reply | Private Reply | To 1 | View Replies]

To: 45Auto
Interesting. I didn't know the history of the cartridge.

I posted a thread on what round I should use in my new 44mag a month ago. I went with the blue tipped safety slugs




5 posted on 02/22/2005 3:01:58 PM PST by Vision (The New York Times...All the news to fit a one world government)
[ Post Reply | Private Reply | To 1 | View Replies]

To: 45Auto

...1. Accuracy: The longer a bullet is in relation to its diameter, the more accurate it normally is. It is a rare .44 Magnum sixgun that does not shoot 300- to 320-grain bullets more accurately than it does 240- to 250 grain bullets. ...

I'm not sure I agree with the longer is more accurate part. A heavier bullet will buck wind better for sure. Other then that I can't see what the advantage would be. Someone care to enlighten me here?


6 posted on 02/22/2005 3:06:39 PM PST by planekT
[ Post Reply | Private Reply | To 1 | View Replies]

To: 45Auto
.44 magnum ... not a bad little gun. I just don't like John Taffin's articles anymore.

Yes we know you're an old timer gun guy that goes way back with a lot of famous people. Stop telling us ever few sentences.

It was horrible in his book about large calibre handguns.

7 posted on 02/22/2005 3:17:14 PM PST by Centurion2000 (Nations do not survive by setting examples for others. Nations survive by making examples of others)
[ Post Reply | Private Reply | To 1 | View Replies]

To: 45Auto
Great article, thanks.

Jim

8 posted on 02/22/2005 3:21:17 PM PST by in the Arena (James Wayne Herrick, Jr. Captain/US Air Force - MIA - Laos - 27 October 1969)
[ Post Reply | Private Reply | To 2 | View Replies]

To: Vision

That is a beautiful gun. My pants just got tight.


9 posted on 02/22/2005 3:28:34 PM PST by mlbford2 ("Never wrestle with a pig; you can't win, you just get filthy, and the pig loves it...")
[ Post Reply | Private Reply | To 5 | View Replies]

To: 45Auto

"...since this is a .44 Magnum, the most powerful handgun in the world and can blow your head clean off, you got to ask yourself one question. Do I feel lucky. Well, do ya punk?"


10 posted on 02/22/2005 3:30:54 PM PST by mc5cents
[ Post Reply | Private Reply | To 1 | View Replies]

To: planekT

I think the "longer bullets are inherently more accurate" stuff comes from the basic idea that longer bullets have more surface contact with the rifling in the barrel, or have three driving bands instead of two, thereby imparting a bit more stability as the slug travels down the barrel. Another idea stems from the connection between bullet weight and the rifling rate for a given caliber. This latter is the heart of benchrest rifle accuracy, but it applies to pistols, too. There certainly are more than enough theories about revolver accuracy and certain revolver/bullet/powder combinations to keep hobbyists busy for years. At this point in my shooting, if I can keep 90% of my .44 magnum rounds on a 8 inch target center offhand at 25 yards, I'm happy.


11 posted on 02/22/2005 3:31:20 PM PST by 45Auto (Big holes are (almost) always better.)
[ Post Reply | Private Reply | To 6 | View Replies]

To: Vision

That's a nice Taurus; how does it match up accuracy wise with its Smith and Wesson cousin?


12 posted on 02/22/2005 3:32:12 PM PST by 45Auto (Big holes are (almost) always better.)
[ Post Reply | Private Reply | To 5 | View Replies]

To: Vision
I used to like those Glassier Safety Slugs. Read the stories about 1 shot stops. Reduced ricochets, shallow penetration in various media. So I bought some for the missus for her S&W 629 for Home defense.

Took them out in my Ruger Redhawk after 1 year of resting peacefully and fired them into an old waterheater at 35 paces. I had 4 thru and thru,1 dented the far side and 1 splattered on the front. Maybe I had a bad lot, but don't believe every thing you read.

13 posted on 02/22/2005 3:34:48 PM PST by earonthief (Semper Fi)
[ Post Reply | Private Reply | To 5 | View Replies]

To: Vision
This is one of my favorites:


14 posted on 02/22/2005 3:35:00 PM PST by 45Auto (Big holes are (almost) always better.)
[ Post Reply | Private Reply | To 5 | View Replies]

To: 45Auto

Im more of a rifle guy myself. But this baby is one nice pistol. Fired it a few times and if I would buy a another (SW) revolver this would be it.


15 posted on 02/22/2005 3:36:48 PM PST by ezo4
[ Post Reply | Private Reply | To 1 | View Replies]

To: 45Auto

Ah lak my 500 grain full wadcutters-sized up to a full .440,and backed by 26 grains of Bullseye.( Ya gotta squeeze a tad when ya load it.)

Hit's pure Hell on Griz !

Ya don't put it anywheres near the gun,ya understand: Ya jest show it to the critturs,an' they faints dead away.


16 posted on 02/22/2005 3:39:31 PM PST by genefromjersey (So much to flame;so little time !)
[ Post Reply | Private Reply | To 1 | View Replies]

To: earonthief
Took them out in my Ruger Redhawk after 1 year of resting peacefully and fired them into an old waterheater at 35 paces. I had 4 thru and thru,1 dented the far side and 1 splattered on the front. Maybe I had a bad lot, but don't believe every thing you read.

I'll take that under consideration, but I believe SS are only meant for soft targets. That may explain your experience. I'm gonna shoot at some melons in a few months with the SS and regular rounds. I'll post the video.
17 posted on 02/22/2005 3:39:38 PM PST by Vision (The New York Times...All the news to fit a one world government)
[ Post Reply | Private Reply | To 13 | View Replies]

To: 45Auto

Piffle and nonsense.

Desert Eagle .50 mag.

LESS recoil. MORE hitting power. LOTS more fun.

BOOM!


18 posted on 02/22/2005 3:40:16 PM PST by BubbaTex (Long time lurker)
[ Post Reply | Private Reply | To 14 | View Replies]

To: 45Auto

I have shot Rugers, RH and BH and they were ok, S&W also, but my favorite is my J.P. Sauer & Sohn Western Marshal. It has just a little over a one pound trigger pull, a real delight to shoot.


19 posted on 02/22/2005 3:41:37 PM PST by eastforker (Ask me about a free satellite TV system!)
[ Post Reply | Private Reply | To 2 | View Replies]

To: BubbaTex

Actually I am eyeing the S&W 500 Magnum for my next purchase, any one here shot one yet? If so share with us.


20 posted on 02/22/2005 3:44:37 PM PST by eastforker (Ask me about a free satellite TV system!)
[ Post Reply | Private Reply | To 18 | View Replies]


Navigation: use the links below to view more comments.
first 1-2021-4041-51 next last

Disclaimer: Opinions posted on Free Republic are those of the individual posters and do not necessarily represent the opinion of Free Republic or its management. All materials posted herein are protected by copyright law and the exemption for fair use of copyrighted works.

Free Republic
Browse · Search
News/Activism
Topics · Post Article

FreeRepublic, LLC, PO BOX 9771, FRESNO, CA 93794
FreeRepublic.com is powered by software copyright 2000-2008 John Robinson