[TenthAmendmentChampion]

http://www.joann.com/static/project/0712/P448334.pdf

Project courtesy of FloraCraft

Designed by Kathleen George
Project size: 9” tall

SUPPLIES & TOOLS:
• Styrofoam™ brand foam
Cone, 4”x9”
Disk, 1”x6”
• Wrapped peppermint candies, 1 or 2 bags
• 1” Decorative ribbon, 20” length
• Holly floral picks
• White craft glue
• Low-temperature hot glue gun*
*Glue gun should only be used with adult supervision.

DIRECTIONS:
1. Glue cone to center of disk.
2. Glue ribbon around sides of disk.
3. Beginning at bottom of cone and working up in rows,
use hot glue gun to adhere peppermints to cone until completely
covered. Top cone with single candy.
4. Press holly floral picks into disk as desired.

[nw_arizona_granny]

LOL, if you are not asking questions, I am.

I like the Cinnamon stick candle holder, but what is the flash point of cinnamon?

Glass conducts heat, is it enough to cause a fire?

I think you are right, about zone 10 on the growing map, you remember, as I always forget...Please.

LOL and I bet if I get out my Sunset growing book it will be an 18, as they keep changing the chart, or have at least 3 times that I know of.

To be safe, if I am going to worry about the zone, I read/check the nursery chart, then I know we are talking about the same chart.

At one time Sunset and the Gov did not have the same numbers on their charts.

But then being me, I often try and grow it anyway.

That is a pretty Peppermint tree.

[TenthAmendmentChampion]

http://www.duncancrafts.com/ProjectDetails.aspx?id=25548a48-9c81-4625-981e-cba3b22ae0d9

Crafting Projects

HOLLY JOLLY HOLIDAY TREE
Create this adorable tree to spread holiday cheer anywhere and everywhere! It’s oh-so-simple to create… just apply Collage Pauge™ Instant Decoupage™ to decorative papers and glue to a foam cone. Make one for every room!

Materials List

Collage Pauge Instant Decoupage™

Aleene’s® Original Tacky Glue®

Miscellaneous
Sequins, snowflake
Freezer paper
Foam cone
12” x 12” paper: Christmas prints - 2 red, 2 lime and 2 turquoise
Scissors
Masking tape
Paintbrush, large
Wire
Pencil
Paper cutter
Foil
Instructions

1. Cut all papers into quarters.

2. Squeeze a puddle of Aleene’s® Collage Pauge™ Instant Decoupage™ onto a small piece of freezer paper. Tape a large piece of freezer paper at corners onto work surface, shiny side up. Brush Collage Pauge™ onto a section of freezer paper slightly larger than one of the cut pieces of paper. Choose one of the colors of Christmas paper and smooth onto glue.

3. Continue adding Collage Pauge™ to section of freezer paper next to the printed paper you just applied and slightly onto the paper. Add another piece of same color of paper onto Collage Pauge™, slightly overlapping onto other paper. Brush Collage Pauge™ on top of papers. You will have a collage of the same color/print of paper that is slightly smaller than the original 12” x 12” sheet you began with.

4. Repeat steps 2 and 3 for each color/print of paper. You should have a total of 6 collaged papers.

5. Let dry overnight.

6. Peel collaged papers from freezer paper. Cut around edges to straighten.

7. Using paper cutter, cut 1” wide strips from each collaged paper.

8. To form tree loops, squeeze Aleene’s® Original Tacky Glue™ onto the back of a strip at the top. Fold the bottom end of strip back and press into glue. Refer to photo. Repeat with for all strips except one, which will be placed around the top of the tree. Let strips dry.

9. To create the tree “leaves,” first choose the color of loops of your choice and apply some Original Tacky Glue™ onto the portion of paper loops where the ends meet. Starting at bottom of cone, one at a time, press loop in place with looped end extending downward from bottom of tree, using bits of masking tape to hold in place. Repeat all the way around the bottom of cone.

10. Repeat process for each layer, alternating colors. Refer to photo. Let dry. Glue un-looped strip of paper around top of tree.

11. Glue snowflakes randomly all over tree, by first squeezing a dot of glue on back of a snowflake sequin. Press in place on a loop. Repeat process for all snowflakes.

12. Freehand draw a star on white paper or matching printed paper using a pencil. Cut out two. Glue back to back (refer to photo) with wire in between. Press wire into top of tree.

---

I'd use christmas wrapping paper! Why spend money on scrapbook paper at $1 a sheet?
10th