I can't get into that site anymore. Otherwise, I wouldn't be asking you. :) I'm not quite that lazy. Almost, but not quite. :)

Hey guys it's me again. I know that this seems unimportant, but if your crapper should be taken out in the event of a terrorist attack, you'll be thanking me.

How to Replace a Toilet

Changing your toilet is an easy project that should take half a day or less. The most common toilet has a separate tank that mounts on top of the bowl. These instructions apply most specifically to this type of toilet. If you have an integral tank/bowl toilet, a flush valve or a wall-mounted toilet, your procedure will vary somewhat.

Whatever kind of toilet you use as a replacement, follow the manufacturer's instructions. Fig. 1 shows the parts of a typical toilet.

TOOLS AND MATERIALS
	Toilet Bowl and Tank	Plumber's Putty	Trap Wrench/Water Pump Pliers
	Toilet Seat	Bathtub Caulk/Sealant	Large Screwdriver
	Bowl Gasket	Supply Valve	Mini-Hacksaw
	Hold-Down Bolts, Washers, Nuts	Flat-Ended Riser Tube	Sponge
	Trim Caps (if not with toilet)	Adjustable Open-End Wrenches	Rustproof Washers

STEP #1

FIG. 1 - Most toilets have a separate tank that mounts on top of the bowl.

FIG. 2 - Check the toilet's rough-in to be sure it's the standard 12" from the rear hold-down bolts to the finished wall behind the toilet.

PREPARATION FOR THE REPLACEMENT

Before purchasing your new toilet, measure the distance from the rearmost bowl hold-down bolts to the finished wall behind the toilet. This is called the toilet's rough-in (Fig. 2). Most toilets are designed with a 12" rough-in. Ask your retailer for help if your rough-in varies.
The first step is to turn off the toilet's water supply. Then flush the toilet to empty its tank, holding the trip-lever down to let all the water run out. Sop out any remaining water in the tank and bowl with a sponge–make sure they're both empty.

STEP #2

FIG. 3 - You can pry off bowl-matching trim caps by lifting under one end with a putty knife or screwdriver.

FIG. 4 - Keep sewer gases out of the house and debris out of the piping by stuffing a rag into the toilet's floor flange opening.

REMOVING THE OLD TOILET

Use a large, adjustable open-end wrench to unthread the coupling nut between the toilet tank and its water supply. You may need to hold the fill valve with pliers from inside the tank to keep it from turning.
Now you're ready to remove the original tank. Most are held to the bowl by two long bolts. The nuts are located beneath the flange at the rear of the toilet bowl. Fig. 11 shows how to work with these.
With the bolts out, you can lift the tank clear of the bowl.
If your toilet tank mounts to the wall and feeds the bowl with a large, sweeping elbow, first remove the elbow. Use a trap wrench or water pump pliers for the slip jam nuts. Or, you can simply saw the elbow with a hacksaw.
Now you can remove the tank from the wall. As you unscrew the tank from the wall, support it so it doesn't fall.
Next, take out the toilet bowl. Typically, the bowl is fastened to the floor with two hold-down bolts and nuts beneath trim caps. Some toilet bowls have four hold-downs.
Pry off each trim cap to expose the bolts and nuts (Fig. 3).
Unscrew the nuts. If you have trouble, you can saw them off. A mini-hacksaw works best, or you can use a regular hacksaw. To protect the bowl's finish from the saw teeth, use masking tape.
Now loosen the bowl/seat unit by rocking it to break its seal with the floor and toilet flange. Once loosened, you can lift the bowl and carry it out of the house. Be sure to hold the bowl level to avoid spilling any trap-sealing water. You may need help to lift the tank and bowl together. Lift it properly with your back straight and put the weight on your legs.
Stuff rags in the toilet flange opening to keep sewer gases out of the house and debris out of the soil pipe while you work (Fig 4).

STEP #3

FIG. 5 - Modern supply valves are compatible with flexible riser tubes for supplying the toilet's flush water.

FIG. 6 - Install the hold-down bolts with some putty to make them stand upright in the toilet flange.

PREPARING TO INSTALL THE NEW TOILET

To get ready for the new toilet, first do a complete cleanup. Remove any old putty and wax from the floor and toilet flange. You can use a screwdriver or putty knife. Clean the floor thoroughly in case the new toilet's footprint is different. Remove the old hold-down bolts–don't reuse them. You may want to clean and paint the wall behind the toilet. If you're going to replace the bathroom floorcovering, this is an excellent opportunity.
At this point, install any new water supply plumbing you plan to add. A new fixture supply valve and flexible riser tube is easy to install and offers shutoff convenience later. The valve attaches to a short length of water supply pipe coming from the wall or floor. Have the riser tube handy but out of the way of the new tank.
Also, inspect the toilet flange for sound condition. It should stick up about 1/2" from the finished bathroom floor.
Temporarily set the toilet in position on the floor over the flange to check for levelness. Check it front-to-back and side-to-side. If necessary, shim under the bowl with non-rusting metal washers.
Install a new pair of toilet hold-down bolts. If there are holes or slots for the bolts in the toilet flange, they should be inserted in the openings (Fig. 6). In a cast iron piping system, the hold-downs screw directly into the wood floor. Whatever the situation, your retailer should have them. Don't try to use ordinary bolts. Install the bolts so they are the same distance from the rear wall.

STEP #4

FIG. 7 - Fix a new wax toilet gasket over the bowl's outlet horn, with the flat side against the bowl.

FIG. 8 - Hold the toilet bowl in position directly above its floor flange, then lower it into place.

FIG. 9 - Hand-tighten the bowl's hold-down nuts. A wrench may break the bowl.

PUTTING IN THE NEW BOWL

Toilet installation goes pretty much the reverse of removal. Handle the bowl and tank with care, since they can crack and chip easily.
Start by inverting the new bowl (or bowl/tank unit) onto a thick, protective padding of newspapers on the floor.
Seal the toilet to its soil pipe flange at the floor by placing a ready-made wax toilet ring gasket over the bowl's outlet horn (Fig. 7). The gasket should be room temperature, and the flat face should go against the bowl. If the gasket has a sleeve, it should face away from the bowl. Don't try to reuse the old gasket–install a new one.
Two kinds of wax gaskets are available: those with plastic sleeves and those without.
The bowl-to-floor joint must be sealed around the edge of the bowl's base, too. You can lay a bead of plumber's putty so it will be squeezed between the toilet and floor. Or, use about 2 lbs. of plaster. Another choice is to caulk the joint with bathtub caulk/sealant. This is probably the easiest method. Ask your retailer to recommend a good caulk for this.
Remove the rag from the toilet flange opening. Now you're ready to set the bowl.
Hold the bowl upright several inches off the floor so its outlet horn is directly above the toilet flange. Then lower it gently (Fig. 8). The hold-down bolts should pass through their openings in the bowl base, and the wax gasket and toilet flange should meet.
To set the bowl onto the floor as well as onto its gasket, rock it carefully from front to back and side to side while pushing down hard. You can rotate it a few degrees each way, too. This forces out the excess wax. As the bowl meets the floor, make sure it is level and square with the rear wall. Don't raise the bowl from the floor while making adjustments, or you'll have to go through the setting process all over again and replace the waxing.
Drop washers over the hold-down bolts and thread on the brass nuts. Tighten the nuts finger-tight only (Fig. 8). Using a wrench at this point can break the bowl. Re-check boths nuts for tightness after several days of use.
If the bowl has front-mounting holes, install two toilet studs with washers and nuts into the floor for the front two holes.

STEP #5

FIG. 10 - Set the spud washer over the flush-valve outlet on the bottom of the tank.

FIG. 11 - Be careful when tightening the tank-mounting bolts to keep from breaking the tank or bowl.

INSTALLING THE TANK

If the toilet tank hardware comes separately, install it. Remember that the trip lever nut probably has left-hand threads.
Now take the rubber spud washer, which fits between the tank and bowl, and set it squarely into the flush valve opening in the bottom of the tank. The washer goes beveled side out (Fig. 10). If there is a rubber tank cushion, set that in place on the bowl. Then pick up the tank and lower it gently into place on the back of the bowl.
Install the two long brass tank-mounting bolts from inside the tank, sliding them down through the aligned holes. Place two rubber washers against the tank and bowl (Fig. 12). Draw the washers and nuts up gently and evenly until they are snug. This finishes your bowl installation.

FIG. 12 - The illustration shows how to arange the washers on the tank-mounting bolts.

STEP #6 - FINISHING UP

Connect the tank's water supply to the inlet valve on the bottom left-hand side of the tank (as you face it). You'll probably have a coupling nut for doing this. The nut threads onto the inlet and works perfectly with a flat-ended riser tube. Don't use any pipe dope on these threads.
Turn on the water and observe the toilet tank as it fills. If there are any leaks, further tightening should cure them. Check to see that the tank fills to the correct level, about 3/4" below the top of the overflow tube.
Tighten the bowl hold-down bolts one turn (no more) beyond hand-tight. Cut off the ends, if necessary, and install the trim caps. You can fill their recesses with plumber's putty (or bathtub caulk/sealant) and press them down over the bolts. Clean up any material that oozes out.
Then, smooth and clean up the excess sealant around the bowl's base.
Now you can test-flush the toilet, checking for water leaks at the floor.
Install the new toilet seat and tank cover, and your installation is complete.

Check your state and local codes before starting any project. Follow all safety precautions. Every effort has been made to ensure the accuracy and safety of the information in this document. Neither NRHA, any contributor nor Aubuchon Hardware can be held responsible for damages or injuries resulting from the use of the information in this document.

Anyone can assign text to any picture. First you type in a word(name, place...anything) and a picture pops up. Then you can assign text to that picture so in essence you've created two links to that particular picture. IMHO, it would have been an excellent site for a dead drop before it became so widely discussed here and elsewhere.

That is not funny and I ask you to please stop it. You and your friends have alot of other places to play. Thanks, in advance.

I agree and seems logical.

Do you think we can get the toilet tank post removed? It's so obnoxious. WE all know how to get to home depot or DIY.

Hey riri, Check out post 11,644...

That is not funny and I ask you to please stop it. You and your friends have alot of other places to play. Thanks, in advance.

Funny!? You'll see how funny it is bub when the terrorists blow your bowl to bits and you have to ask the Pizzeria down the block to use their facilities.

When the color code goes to yellow I always check to ensure that I have an extra ballcock and chain around. You can't be too careful in this day and age.

That moron is a sleeper troll did you see his keywords? LOL!

And we still have George Tenet!

Liz Freeper's are frying him on that hread, read it ;)

I was hoping you wouldn't see that one, JP. I did not ping you to that one on purpose. I knew it would upset you as much as it did me. What a world we live in.

Tis just a jealous Hobbit ;) Because this thread has substance

Join the worlds first Paranormal ISP! And GET A GREAT DEAL!!

I've seen Sean on several threads

It says:

The Jihad Groups
Our victory (stopping) is only in jihad

Wasn't one of the reported gasoline thefts also in Arizona?

CALPERNIA VAVOOM!!!

He seems to be a few bricks shy of a load to begin with.

ROFLMBO!

The Hobbits have laid claim with 65,000 posts

I forgot Bush would be in NM!