Posted on 11/14/2006 12:04:47 PM PST by Red Badger
In a poster session at the upcoming 25th Army Science Conference, to be held 27-30 November 2006 in Orlando, the Army Research Laboratory’s Vehicle Technology Directorate is presenting an overview of three unconventional engine concepts being developed under its sponsorship.
The three engines are: a low-power, high energy-density Nutating engine targeted at unmanned air and ground vehicles, auxiliary power units, and generator applications; a turbine concept that uses semi-closed engine cycle synergistically coupled with a vapor-absorption refrigeration system; and the Bonner Engine, a new, two-stroke combustion engine concept in which two cylinders reciprocate in a 90° X-configuration, each between two semi-fixed, movable pistons.
.The Bonner Engine is unmatched in its ability to operate at maximum efficiency over its entire RPM range, and in its ability to deliver constant power at any desired altitude. It is expected to be the most fuel-efficient intermittent combustion engine ever conceived. The Bonner Engine will greatly reduce fuel consumption for power generation applications, and will allow both air and ground vehicles to achieve significantly increased range and/or payload. —P. L. Meitner, Army Research Laboratory
Bonner2 Cross-section of the Bonner Engine.
The pistons contain the fuel nozzles—and, in a gasoline application, the spark plugs. Each moving cylinder incorporates the intake and exhaust ports/valves and is open on its ends. A novel, dual-offset crankshaft which generates zero side loads on the cylinders and pistons enables the Bonner’s geometric configuration. (See diagram at right.)
Each reciprocating stroke is stopped and countered (at dead center) by compression and ignition—not by the crankshaft—and all pressure on the crank is power-producing.
Features of the Bonner Engine include:
*
Pre-Compression. A pre-compression chamber surrounds each end of the moving cylinder, and provides an initial boost to the incoming charge. The pre-compression chamber can be configured to provide a constant boost pressure, regardless of altitude or air density. *
Variable Compression and Induction. Each semi-fixed piston has a small range of motion (actuated hydraulically) which is used to continuously vary the overall compression ratio with engine speed. At low speed (idle) the piston is in its lowest (innermost) position, resulting in the highest overall compression ratio. At higher speeds the piston is moved progressively outwards, giving lower overall compression ratios.
This mechanism also allows for continuous variation of air inlet size, timing and duration with engine speed. *
Exhaust Energy Recovery. Exhaust passes through a rotary valve which, at the appropriate time, routes it to a chamber above the moving cylinder, helping to push the cylinder downward during its power stroke. During the moving cylinder’s upward motion the rotary exhaust valve vents the exhaust overboard.
Unlike conventional 2-stroke engines, the Bonner Engine utilizes separate fuel and oil supplies, and conventional piston rings provide complete isolation between the lubricating oil and the fuel/air flow, resulting in a cleaner burn.
Since the engine’s combustion chamber intake and exhaust are located at opposite ends of the moving cylinder, the incoming charge does not have to change direction between inflow and outflow, thus enabling uni-flow scavenging. This, plus the totally controllable exhaust back pressure, combined with the variable intake charge timing assures that scavenging losses will be negligible.
Because the Bonner Engine uses conventional piston configurations, all knowledge in existing data bases can be utilized to optimize the burning characteristics (for heavy or gasoline fuel), thus minimizing engine emissions. Also, the unique, two stage compression process of the Bonner Engine allows for the best possible mixing of fuel and air. This generates a very even combustion event, and offers an excellent chance of achieving Homogeneous Charge Compression Ignition (HCCI), the holy grail of piston engine research.
Phase I development of the Bonner engine has been completed, and the developers are working on a 600cc prototype engine under a current Phase II contract.
old old news.
Seems this junk gets dug up every ten years.
Check this one out.
http://bourke-engine-project.com/index2.html
Rest in Peace, old friend, your work is finished.......
If you want on or off the DIESEL "KNOCK" LIST just FReepmail me........
This is a fairly HIGH VOLUME ping list on some days......
This is the replacement for the Self-Stroking Boehner Engine.
There are many improvements over the original, the most important being that this model actually does something besides sit there and look pretty.
Does it pass out checks on the House floor?...........
saving
Is this like the Pontiac two-speed powerglide transmission, sort of [scratches head?]
It looks promising, if the Army is studying it..........
Oh, they're way beyond that now. This one actually earmarks it's own fuel costs, plus a few extra bucks, so it actually pays YOU to run it.
"The pre-compression chamber can be configured to provide a constant boost pressure, regardless of altitude or air density. *
Variable Compression and Induction. Each semi-fixed piston has a small range of motion (actuated hydraulically) which is used to continuously vary the overall compression ratio with engine speed. At low speed (idle) the piston is in its lowest (innermost) position, resulting in the highest overall compression ratio. At higher speeds the piston is moved progressively outwards, giving lower overall compression ratios.
This mechanism also allows for continuous variation of air inlet size, timing and duration with engine speed."
So, would this thing never need a tune-up?
Hey, that Powerglide was a great drag racing transmission! I had one in my 66 El Camino w/327. Fun was had by all.
So, would this thing never need a tune-up?
Things will still wear out. They haven't overcome friction yet...............
Oh man! We had a 307 '68 El Camino with dualies and Hookers! The powerglide was in our '64 Le Mans convertible. This time of year, put the heater on and top down, hit the stride at about 70 m.p.h. and the machine pulls you down and out on a silent whoosh...yeah!
I miss when hubs and I had cars. Once I helped him change the distributor on the LeMans - it was our anniversary, complete with trouble light, very romantic! LOL!
I used to know the order of the firing of the pistons.
He said "Self-stroking Boehner."
huhuhu hu....
They're still the same..............[Bob Seger].......
What mode of transport do you have now? I have a couple of motorbikes, and I could see this x-4 engine in a racebike. Looks like it could be efficient, and light.
interesting seeing reed valves again. I have a dirty old 2-stroke dirt bike that uses those.
Disclaimer: Opinions posted on Free Republic are those of the individual posters and do not necessarily represent the opinion of Free Republic or its management. All materials posted herein are protected by copyright law and the exemption for fair use of copyrighted works.