Skip to comments.Graphene made in a kitchen blender
Posted on 04/23/2014 1:53:19 PM PDT by neverdem
Shear mixing could be used to produce graphene flakes in bulk © CRANN
While next generation electronic devices need ultra-pure, monolayer graphene produced by mechanical exfoliation or chemical vapour deposition, everyday electronics such as batteries and solar cells are produced using solution coating. Therefore, to use graphene in these kinds of electronics engineers require huge amounts of high quality graphene flakes suspended in solution.
In 2008, Jonathan Coleman at Trinity College Dublin and colleagues showed that extremely pure graphene could be exfoliated from bulk graphite dispersed in common organic solvents by bombarding it with ultrasound, a process called sonication.2 However, this method is difficult to scale up. Unfortunately, processes that can produce graphene in bulk, such as chemical reduction of exfoliated graphene oxide, introduce holes and impurities, crippling the materials fantastic properties.
Coleman says that they were set on the road to their discovery when speciality materials manufacturer Thomas Swan approached Trinity to come up with a way of making large amounts of defect free graphene. Not knowing where to start, the researchers drew up a list of crazy ideas and shear mixing, where high speed blades are used to create substantial shear in a fluid, was one of the first they investigated. It was at the top of the list purely because it was so easy, quick and cheap to do, says Coleman. And happily, it worked.
Defect free graphene was exfoliated using the shear technique © CRANN/SuperSTEM
Further investigation revealed that relatively defect free graphene flakes 300800nm in size, typically less than 10 atoms thick and including some monolayers, had been made virtually indistinguishable from those of sonicated graphene. Using the shear technique the team has already exfoliated a range of materials including boron nitride and molybdenum disulfide. They even produced small amounts of graphene in an ordinary kitchen blender. The team theorise that shear more efficiently slices off layers of graphene than sonication because a greater proportion of the energy goes into pulling each layer sideways and away from those above and below.
As shear mixing is already widely used in industry, the researchers see no obstacles to scaling up the process. In a 10m3 tank they calculate it should be possible to produce over 100g of graphene per hour far more than any other process. The teams high quality graphene has already been used to reinforce polyethylene teraphthalate just 0.07% graphene increased the polymer's strength by 40%. More remarkably, they produced strain gauges that were much better than their commercial counterparts simply by dipping ordinary elastic bands in the suspension.
Materials scientist Arkady Krasheninnikov of the University of Helsinki in Finland describes the research as very simple and yet very impressive. He adds that the team's demonstration that multiple layered compounds can be exfoliated could open the door to bulk thin films containing several different monolayer compounds.
1 K R Paton et al, Nat. Mater., 2014, DOI:10.1038/nmat3944
2 Y Hernandez et al, Nat. Nanotechnol., 2008, 3, 563 (DOI: 10.1038/nmat3944)
Hey, let’s throw it in a blender.
But wait! There's MORE!.........If you call right now we''ll throw in a SECOND BLENDER FREE! (just pay shipping and handling)..............
What’s black and goes around at 100 miles per hour?
Graphene in a blender.................
I’ve been following the graphene stories for a number of years. The more I read, the more I get the feeling it could change our future more than any material ever discovered or invented - by several orders of magnitude.
I’d still like to see a graphene based “capacitor as battery”. Or a graphene ribbon supporting a space elevator. And how about a man powered aircraft with single layer graphene skin?
Graphene sounds like a promising technology.
For the other 99.99% of us: http://en.wikipedia.org/wiki/Graphene
now that’s just plain funny.
"Is there anything else in the blender?"
Elephant in a microwave.
frog in abblender
FReepmail me if you want on or off my health and science ping list. Anyone can post any unposted link as they see fit.
Thank you for posting this article and for the ping. My hubby is the director of engineering and quality at a printed wiring board
manufacturing facility. I sent him a link to this post because it is possible that graphene could make circuit boards a lot sturdier,
which would make them compatible with uses that are a lot rougher than just sitting in a radio or TV until they die of boredom.
Disclaimer: Opinions posted on Free Republic are those of the individual posters and do not necessarily represent the opinion of Free Republic or its management. All materials posted herein are protected by copyright law and the exemption for fair use of copyrighted works.