Free Republic
Browse · Search
News/Activism
Topics · Post Article

To: dennisw
These tiles are super hi tech ceramics of some kind?

Not really..they were even selling off spec ones for industrial use in the late 80's-90's. We had some at work. They were just a glorified zirconia fiberglass-like refractory wool molded and fired into lightweight "Fire Bricks". Some were glazed. They were very good insulators. You could hold on in your hand and torch braze small parts on the upper surface.

10 posted on 03/28/2009 3:24:25 PM PDT by Gorzaloon (Roark, Architect.)
[ Post Reply | Private Reply | To 4 | View Replies ]


To: Gorzaloon

Many thanks.... I have a large box of lightweight firebricks from 1970 or so. We made a quicky kiln with them by stringing nichrome wire inside. Held down by nails or two prong wall fasteners


15 posted on 03/28/2009 3:34:37 PM PDT by dennisw (0bomo the subprime president)
[ Post Reply | Private Reply | To 10 | View Replies ]

To: Gorzaloon; dennisw
Gorzaloon wrote: " 'These tiles are super hi tech ceramics of some kind?'

Not really..they were even selling off spec ones for industrial use in the late 80's-90's. We had some at work. They were just a glorified zirconia fiberglass-like refractory wool molded and fired into lightweight "Fire Bricks"."


Zirconium, nor its impure oxide Zirconia are not used in the manufacture of the Shuttle tiles, according to NASA.

Instead the High-Temperature Reusuable Surface Insulation Tiles (HRSI) are made of nearly pure silica.

High-Temperature Reusable Surface Insulation Tiles


"The HRSI tiles are made of a low-density, high-purity silica 99.8-percent amorphous fiber (fibers derived from common sand, 1 to 2 mils thick) insulation that is made rigid by ceramic bonding. Because 90 percent of the tile is void and the remaining 10 percent is material, the tile weighs approximately 9 pounds per cubic foot. A slurry containing fibers mixed with water is frame-cast to form soft, porous blocks to which a collodial silica binder solution is added. When it is sintered, a rigid block is produced that is cut into quarters and then machined to the precise dimensions required for individual tiles.

HRSI tiles vary in thickness from 1 inch to 5 inches. The variable thickness is determined by the heat load encountered during entry. Generally, the HRSI tiles are thicker at the forward areas of the orbiter and thinner toward the aft end. Except for closeout areas, the HRSI tiles are nominally 6- by 6-inch squares. The HRSI tiles vary in sizes and shapes in the closeout areas on the orbiter. The HRSI tiles withstand on-orbit cold soak conditions, repeated heating and cooling thermal shock and extreme acoustic environments (165 decibels) at launch..."

NASA: High-Temperature Reusable Surface Insulation Tiles



The space shuttle engine contains a copper-silver-zirconium alloy:

"The space shuttle engine, for example, uses a copper-silver-zirconium alloy..."

Structural Materials in Aerospace Systems

27 posted on 03/28/2009 5:46:06 PM PDT by bd476
[ Post Reply | Private Reply | To 10 | View Replies ]

To: Gorzaloon; dennisw

I believe they are ceramic in some form or other. Mr G’s father was a scientist (ceramic engineer) and helped develop them.


30 posted on 03/28/2009 6:33:59 PM PDT by Grammy
[ Post Reply | Private Reply | To 10 | View Replies ]

Free Republic
Browse · Search
News/Activism
Topics · Post Article


FreeRepublic, LLC, PO BOX 9771, FRESNO, CA 93794
FreeRepublic.com is powered by software copyright 2000-2008 John Robinson