Need advice on concealed carry handgun

Me

[org.whodat]

Well haveing owned a 410 shotgun. I really have doubt's about anyone with a concealed weapon that has to ask someone else what he should carry. Maybe you should start out with a good gravel shooter and some marbles.

[Mulder]

If you want SA/DA, I would recommend a Sig-Sauer.

If you want a .40, try either the Sig 229 or Sig 239. The 229 holds 12 rounds, while the 239 holds 7 rounds and is single stack. (I'd also recommend checking out the 357Sig cartridge before you buy anything. It's basically a 9mm bullet in a .40 casing). Both the Sig models I mentioned earlier are available in 357 Sig, and it's just a simple matter of switching out barrels to change calibers. With the 239, it takes different mags also.

For a holster, try a Don Hume inside-the-waistband holster if you want something inexpensive but good. Also, look at Milt Sparks Versa-Max. They are about $100, but everyone who has one loves it. I just ordered one for myself.

One item that is essential to comfortable carrying is a good belt. I recommend the Wildneress 5-stitch tactical belt. You can cinch it down so it is comfortable, yet secure enough to hold the gun.

You'll also probably want to change your clothes in order to carry. Pants and shorts will need to be 1-2 sizes bigger, and shirts one size larger. Button-up shirts work great for concealment, unless it's windy, then an oversize t-shirt works great.

Hope this helps.

[Mulder]

Plus, don't use rubber grips. They attract moisture and perspiration.

And they will stick to your shirt, making drawing more difficult.

[Monty22]

A Glock 36 with holster IWB Clip from www.kramerleather.com

Can't go wrong there, trust me. Until we know for sure that the 10 round limit goes away, it makes little sense to buy a modern gun (even though I have) that it big and .40 or 9mm. Might as well get .45.

[yarddog]

As long as you are able to carry it comfortably concealed there are a whole lot of good ones. If you limit yourself to big bores then there is one that I always considered a little jewel of a gun and that is the Star PD. It is light, compact and a good shooter.

It hasn't been made in many years but I still see used ones fairly often.

I am not particularly fond of Glocks but concealed carry is one place some of their compact models make a lot of sense.

[Shooter 2.5]

When you're carrying against your skin, smooth is the way to go.

I took the rubber grips off my Stainless .45 and the area under the grips was pitted. It went back to the factory and they cleaned up the pits. I don't recommend rubber. I love my phony ivory grips.

I also believe in the flat mainspring housing on 1911's. When you fire with your thumb on the safety where it belongs, the palm is cupped so the grip safety isn't engaged like it should. Flat housings correct the problem.

I carry all the time and my rig is the exact same for the IDPA matches.

[Luke Skyfreeper]

In that case, I would be tempted to go with those who recommend a Sig.

[annyokie]

I get sweaty palms, but smooth is the way to go for me. TG, I haven't had to throw down on anybody, but it makes it easier for those drills.

[ChuckHam]

Well haveing owned a 410 shotgun. I really have doubt's about anyone with a concealed weapon that has to ask someone else what he should carry. Maybe you should start out with a good gravel shooter and some marbles.

What the hell are you talking about? I've fired many handguns over the years but never carried concealed. I'm not the least worried about my ability to handle the weapon or fire it accurately. If you had read my post I'm primarily concerned with concealability in a handgun of .40 or .45 caliber. Your comment is insulting and of no value here. Sounds to me like you're a person that doesn't like concealed carry. Too bad.

[Shooter 2.5]

I tried that Galco Summer Special and the rough interior made it impossible to get the gun out.

The Royal Guards are rough on the outside to grip the pants and a silky smooth interior for a fast draw. Plus, the split loops allow the holster to be captured om each side of the pants belt loop.

[annyokie]

Pay no attention to that man behind the curtain. You'll get good advice here.

[ChuckHam]

So far I'll have to agree with you. I'm searching the internet for the items you guys have recommended so far. I really appreciate the info from concealed carry veterans.

[ChuckHam]

Now I'm off to bed. See you guys on the thread tomorrow morning!

[Aarchaeus]

Kahr K40

[Don Carlos]

Gotta agree on the lightweight .32 cal. I Own a Springfield Ultra-compact V-10 (Nice piece!), a Taurus M-85 snubbie .38 special, and a Kel-Tec P-32. Guess which one goes with me without fail? That little 7 ounce Kel-Tec could be concealed in your speedo if you go to the beach!

I like the feel of the V-10, and the ease of concealing the snubbie. But the .32 with a IWB spring clip doesn't take two seconds to clip inside the waist-band.

My two cents.

[Mulder]

It needs to have a small frame since I live in San Antonio

If you go with the right set-up (belt, holster, and shirt), you can carry even a full-size handgun comfortably.

Conversely, if you don't do the belt and holster right, carrying a compact gun will give you fits.

[Shooter 2.5]

Great. Another V-10 fan.

I let a young lady shoot it and she was convinced she was shooting a 9MM.

[jrp]

Take a look at the Smith&Wesson CS45.
Ultra-compact traditional DA auto.
Here are the specs:

SKU: 103014
Type: Pistol
Model: CS45
Caliber: .45 ACP
Barrel Length: 3-1/4"
Capacity: 6 Rounds +1
Action: TDA
External Safety: Ambidextrous
Hammer: .260" Bobbed
Trigger: .305" Combat 3-1/4"
Grip: Hogue Wrap Around Rubber
Front Sight: White Dot
Rear Sight: Fixed 2-Dot
Frame: Compact
Finish: Satin Stainless
Over all length: 6-1/2"
Weight: 23.9 ounces
Material: Aluminum Alloy / Stainless Steel

[Travis McGee]

10 X .45 all the way!

[Don Carlos]

V-10 is a lot of gun for the price. Had mine worked by a local Ex-USAF armorer, for the princely sum of $35.00 and it made a nice pistol VERY nice. Basically, a hand filed and polished trigger and re-tensioned (by bending) spring, and it felt like a $1000 custom job.