Posted on 12/16/2003 5:29:21 PM PST by aculeus
It depends on which way current-flow goes... Reverse the positive and negative terminals on the commutator, and the mechanical force reverses.
BTW, the idiot who wrote this is obviously an idiot... There are no electric "engines." Only electric "motors." ;)
I'm not up on battery technology, but this may or may not be a weak point in the system. A relative owns a Honda hybrid, and he noted that the battery is supposed to be replaced every year at a not-inconsiderable cost. (Though I don't recall the figures so I don't know what the savings are...) And that is in a car that presumably relies less on its battery than one these vehicles.
Whether the battery materials can be inexpensively recycled, whether they're using better batteries... there's a lot I don't know. I'd be happy to see something like this succeed, but I'm sceptical of reports that speak so glowingly of a future of the sort where "at the mere pressing of a stud, one will be able to converse directly with anyone anywhere across the globe."
Dang it, where are those flying cars they promised?
Not necessarily an idiot. More likely a recent product of the American public education system.
Right!
Actually, according to Websters definitions, either term could be used interchangeably. (really, look it up). It is far, far more common to refer to electric motors as 'motors' not as engines, particularly in the US. Calling an IC engine a motor is completely common though.
I mentioned this idea (motor in wheels) on a thread once and was promptly imformed by Freeper engineers that it wouldn't work for various reasons (don't remember the thread and it's been quite a while). Maybe some engineers could comment on this. Also on what the use of the new (neodymium) 'super' magnets would mean to this type of arrangment as far as efficiency and power output.
2. I also have some trouble believing that 1700 rpm is the diesel engine's optimum speed -- it sounds too low.
It appears the biggest saving is the use of direct drive motors. This eliminates losses from friction, slippage, etc. in power trains. No transmission, no differential. One of the biggest plusses about front wheel drive cars is the elimination of the hypoid rear axle. The hypoid gear set, unlike spur gears, relies on sliding of the gear tooth surfaces. This is why they require 90W gearlube and run so hot. Commutatorless electric motors, using Hall sensors and electronics instead of graphite-on-copper brush systems have really come a long way recently and efficiencies better than 90% are not uncommon.
The following is a reprint of Chapter III from the Fish Carburetor Book by Michael H. Brown, pages 11-12 (1982): III.
The 100 MPG Carburetor Myth
There have been numerous books and plans written purporting to "reveal the secrets" of the famous "200 mpg carburetor," a device supposedly built in 1935 by Charles Nelson Pogue of Winnipeg, Canada.
As of this writing Mr. Pogue is in a nursing home in Winnipeg, Canada. Several of our customers have visited with him. Each came away with a slightly different story. Mr. Pogue actually did manufacture a carburetor he titled the "Winnipeg" in the late 1930s; 317 all told. One of our customers had one and claimed it delivered 35 mpg on a Ford Mustang with considerable loss of power; however, he agreed to let us have it for testing and we are still waiting.
There are two problems with the "Pogue principle," which is being touted in high mileage seminars and books all over the country.
The first is that the Pogue carburetor violates the first law of thermodynamics, a commonly accepted scientific postulate that has been with us since 1830. The law is written as follows: U = q + w Or, in simple English, if you have chemical energy in a system (U) in its expenditure, it must equal q (heat) plus work (w). That is, if you have 100,000 BTUs in a gallon of fuel in which you then burn the end productsin a system operating at 30% efficiencyyou will have 30,000 BTUs of work and 70,000 BTUs of heat.
Anything you put inside the combustion chamber can do only one of two things during the ignition stroke. Produce energy (mechanical movement) during the reaction. Absorb energy (leave out the exhaust as heat) during the reaction.
There has been a lot written about the "unburned particulates" furnishing the extra fuel for the extra 50 mpg or so, but if youll check the Fish dynatune emissions levels youll see there arent enough of them to get you another 300 yards down the road. The second problem encountered with Pogue-type devices is thatin some instancesthey actually predate the carburetor.
Lets elaborate in both cases.
Back before the carburetor as we know it came into being in the 1890s there were several novel methods of getting fuel into the engine. One method was using a kerosene-soaked rag to drip fuel into the engine. Another methodthat became quite commonwas allowing air to pass over the surface of gasoline and then to be sucked into the engine. Sometimes a valvecalled a "mixing valve"would be positioned between the fuel reservoir and the engine. The valve would pop open when the downward motion of the piston created enough suction. This methodand variations of ithave been touted all over the United States in "100 MPG CARBURETOR" seminars sponsored by various individuals as being the "ultimate" in sophisticated fuel systems, usually with exhaust heat or radiator water added to "vaporize" the fuel much more effectively than a standard carburetor.
There are a number of things wrong with the concept of such a "100 MPG" system.
The first is that the gasolines in use during the days of the mixing valve were far more volatile than the ones in use today. Some of you may remember when you could stand ten feet away from an open pan of gasoline, light a match, and watch the gasoline immediately catch fire.
Gasolines were changed in the 1930s with the advent of the catalytic cracker now used in petroleum refining. Carburetors like the Pogue, which depend on easily vaporized gasoline, simply will not work with todays gasolines.
The second seminar-taught error is the method of using exhaust heat or radiator water to heat the fuel to the "vapor" point to extend the mileage. Warming or preheating fuel does have some value, but its limited. Consider using hot water from the radiator to vaporize the fuel first.
Todays gasolines do not completely vaporize until they reach 450º Fahrenheit heat, while the maximum temperature of the water in todays pressure radiators reaches only 250º Fahrenheit. You just cant heat a substance to 450º Fahrenheit using a 250º Fahrenheit heat source. At least, not on this planet.
Exhaust heat works a bit differently.
It is the function of an internal combustion engine to change chemical energy into heat, and then the heat into mechanical movement. If the heat is not changed into mechanical movement it simply leavesas heat. Any time you feel heat coming off an engine you are feeling wasted energy. The exhaust ports of an engine that operated at 100% efficiency would be ice-cold to the touch since ALL the heat would have been changed into mechanical movement. Which means that the more efficient your engine is the less exhaust heat youre going to have.
For example, if you have 600º Fahrenheit exhaust heat produced by one gallon of gas over a 20-mile trip and you use "exhaust heat" to "vaporize" the fuel and go 60 miles, what produces the 600º Fahrenheit heat for the next 40 miles?
If you answered "two more gallons of fuel," go to the head of the class!
Seriously, there are ways to go several times the distance on a gallon of fuel (none of them involving carburetors); its just that the foregoing examples arent two of them. In short, Charles Nelson Pogue was a machinist with no formal training in thermodynamics and may have actually believed that what he was attempting would work. All a carburetor can do is meter and atomize fuel in correct proportion to air.
Any further increases have to come from increasing the thermal efficiency of the engine itself (such as raising compression) or reducing rolling friction. And this last is why a diesel locomotive with steel wheels will go ten times as far on a gallon of fuel as a diesel truck of the same weight with rubber tires.
For Pogueor any similar carburetorto go 100 mpg on a gallon of fuel on a vehicle normally going 20 mpg, the air/fuel ratio would have to be in the neighborhood of 75 to 1 or better.
Any second-year college chemistry student knows that.
Probably a 'stationary engine' type of engine that is designed to run at a specific speed only. Load increases injector volume to maintain a constant speed no matter what the power draw. Some of those China Diesel generators I've seen seem to run ar pretty low speeds. That's why they seem to run for ever, I immagine.
maybe the saudi and chavez governments will be able to run on hot air because their oil will be useless in 20 years. there is going to be a lot of madresses without money pretty soon.
BTW, my own truck's diesel engine has no interest at all in reving above 2000 RPM. I imagine the torque peak is around 1700.
Disclaimer: Opinions posted on Free Republic are those of the individual posters and do not necessarily represent the opinion of Free Republic or its management. All materials posted herein are protected by copyright law and the exemption for fair use of copyrighted works.