Posted on 07/02/2021 7:22:23 AM PDT by Berlin_Freeper
Welcome to The Bicycle Thread. A monthly PING List for bicycle enthusiasts to share experiences, information and ideas.
1. Puncture flats, round, due to something as small as a 1/4" piece of wire going thru a tire with little tread.
2. "Pinch" flats, around here these are usually due to faulty "bunny hops" over a curb, small horizontal slits, usually two in the same area. Can be front or back tires.
3. Abrasion flats, due to bare spots in the tire, usually as a result of "drifting" = locking the wheel up and skidding.
To avoid flats, there are many options (besides the obvious of avoiding glass, debris, holes), most of which you can combine:
1. Reduce tread width. Use a bike with good quality (like with Kevlar) narrow tires (street bikes). While having less tread thickness, these also have much less contact area with the road, even being as small as your little finger, thus less likelihood of running over something sharp. Keep fully inflated for that reason.
2. Increase tread depth. Use a mountain bike with heavy tread.
3. Get Thorn Resistant tubes (adds some weight, but less than the bottle of water you just drank).
4. Try tire liners (not rim strips) that go inside the tread. Slime 20093 Tube Protector; Stop Flats2 MTB Bicycle Tire Liner, etc. Secure well as they can shift and cause pinch flats. Armour Tire Insert is in a cla$$ by itself, as with the cost.
5. Try solid tires. Tannus seems to be a $tep above.
6. Try tubeless tires.
7. Self-sealing tubes. Not recommended.
Now my instructions on patching a tube:
1. Remove the wheel (axle nuts, if used, are usually 15mm) and deflate the tube (cock the pump nozzle to one side so you hear air and rotate the tire somewhat). Then remove the tire from off the rim (if necessary, use a tire lever to pry off one side of the tire, beginning a foot away from the valve, and after one side of the tire is off then carefully push any of the tube up into the tire, then squeeze the tire and then push the tire lever all the way under the tire, lean the tire to the side and slowly pry it off, carefully ending with the valve).
2. Find out the specific location of the tire leakage by inflating the tire (maybe about 6 pumps using a full pump as this $10 one) until it is spongy like a balloon (you can press it in about an inch) but not stressed. Then, if leak is not found, rotate each side of the tire past your cheek so you can feel the leak. Or, if necessary, vertically submerge each section of the tube in water (begin with the valve) and look for bubbles.
3. Next, clean/dry the area around the leak and if necessary use a marker to make a wide circle around the leak so that you know where it is. Note that if possible, it is best to leave the tube inflated until we get to step 6. Also, try to have clean fingers and minimize skin contact with the leak area.
4. Next, use a buffer to friction-clean the wide area around the leak (blow away any sand if you use sandpaper), and then spread a thin coating of rubber cement onto the leak area on the dry tube, rubbing the cement into the tube for a few seconds until it begins to dry. Note that it is best to use cement that is made for rubber patches, like Slime 1050, and do NOT use super glue or anything else but rubber cement)
5. Next, let the rubber cement dry for about 2 - 3 minutes (outside in windy or sunny warm dry weather it can dry faster), while you slowly remove the foil backing from the patch, holding the edge of the patch. You may also remove the cellophane cover if you want, since that does not stretch like the rubber does - but AVOID putting your fingers on the bottom of the patch (where the foil was).
6. After the cement is dry (it will look dry) deflate the tire if there is much air left in it, and then place the patch over the center of the leak. Then place the tube on a smooth hard surface and press down all area of the patch
7. Wait about a minute or two before putting some air into the tube (about 3 pumps) to make sure the patch is holding and there is no leak (note: some tubes are made of a different material which feels very smooth, kind of like plastic, and for these you may need to repeat steps 4 and 5 if the patch begins to peel off). If all is well then place the inner tube into tire and onto the bike and re-inflate it (about 16 pumps).
Hope this helps. http://peacebyjesus.net
to her... me Me ME MEEEEEEEEE!!!
I picked up a Zizzo Forte folding bike earlier this year.
Very happy with it. I have done some mods, a new free cluster and seat. Both minor mods, makes a lot of difference...
Anyone here into fat and plus size tire bikes? I ride a salsa timberjack in 27.5+. I normally run 3.0s which are my all around tire.
—
I run 27.5 x 2.8” Maxxis Rekons on my hardtail which I really like. Running tubeless I can drop the pressure down to 12 PSI in the from and 14 PSI in the rear for an amazingly plush ride, for a hardtail. The lower pressure allows the tires to conform to the terrain.
The right tire depends a lot on your local terrain, plus your personal preference. In the greater northeast, we’ve got rocky soil, roots, mud, and hard pack. For me the Rekons work great. They hang up well on rocks but have fairly low rolling resistance.
Thank You for the thread FRiend! 👍🚲🚵♀️
Thank you for the info on avoiding flats.
As for the second part of your post, I’ve been changing bicycle tires since I was 10 years old. I’ve also changed motorcycle tires, automobile tires, and have assisted with changing semi-truck tires.
Good for you, by the grace of God. I should think assistance is welcomed in changing semi-truck tires! But maybe the tutorial on patching bicycle tubes can help others.
I’m running WTB rangers front & back. I’ve found these to work well in multiple situations. I’m also still using tubes for the simple reason if anything goes sideways they can always be fixed easily. I’ve thought on/off about getting a fat bike and likely will when the bike crunch subsides. For now thought my 3.0s work well even in dry sand. Although a fat tire would make it easier. BTW I’m also in NE.
First time this year I saw what we call The Pink Cadillac".
These two were collecting trash along the riverbank. On a Sunday!
My new Nike. The fabric allows cool air to my feet while I ride and they glow in the hall when I use the bathroom in the middle of the night.
You are welcome FRiend!
Soviet plane crashes into Stößensee Berlin, April 6 1966 (YouTube)Get out of your rat-lines and go exploring. You might learn something!
Today was cloudy and cool so I rode around the Müggelsee. I decided to get off my usual trails and saw some new places. One trail was really enjoyable and right next to the lake. I was happy I finally found this way. Then I saw what looked like a memorial that had pictures so I stopped to investigate this because you're not surprised to see such a thing along a road (car accident, etc) but not here on a trail by the lake.
Pandas at the Berlin Zoo are the only pandas in Germany.
Disclaimer: Opinions posted on Free Republic are those of the individual posters and do not necessarily represent the opinion of Free Republic or its management. All materials posted herein are protected by copyright law and the exemption for fair use of copyrighted works.